Volt & Grain

Guides / Renovation

How many sheets of plywood for a van conversion

Count a van build one thickness at a time and nest each list on the sheet you can buy. A worked example shows the same van floor taking two sheets or three.

Published13 November 2026
Sources2 cited

There is no single number of plywood sheets for a van, and a figure without a parts list behind it is a guess. The count depends on how many thicknesses the build uses, how you split each job into pieces, the blade you cut with, and which sheet the yard near you sells.

So this page does not give you a number. It gives you the method that produces yours, and a worked floor run through this site’s cut list calculator that shows how far apart two reasonable answers can be.

The short version

  1. Make one list per thickness. The calculator nests one thickness at a time, and you buy one thickness at a time.
  2. Write every part as a rectangle, including the ones with notches.
  3. Nest each list on the sheet you can actually buy, with your blade’s kerf.
  4. Add up the sheets per thickness. That is the shopping list.

Do not divide the van’s surface area by the area of a sheet. The next two sections show why.

Why dividing by 32 square feet undercounts

A 4 × 8 ft sheet is 32 square feet, and it is tempting to add up the floor, walls and ceiling and divide. That assumes every offcut finds a use. Three things stop that happening.

  • The blade takes material. Every cut removes the width of the blade. The calculator subtracts kerf on every cut, and its test suite pins the simplest case: two parts that are each exactly half a sheet share one sheet when the kerf is zero, and need two once the blade takes 3 mm.
  • Cuts run edge to edge. The calculator only produces nests a track saw or a panel saw can cut, where every cut runs straight across the piece on the saw. It does not count material you could only free by cutting around a corner.
  • An offcut only counts if a part fits it. A long strip down the side of a sheet is area on paper. If every part still to cut is wider than the strip, it is scrap.

Grain adds a fourth limit on parts that show. The calculator assumes face grain runs along the sheet’s length, and a part marked as grain-critical is never turned to fit a gap.

Worked example: one floor, split two ways

Take a van floor 70 in wide and 120 in long, measured at its widest and treated as a rectangle. It is an example, not a particular van, so measure your own. Its area is 8,400 square inches, about 58.3 square feet. Divided by a 32 square foot sheet, that is 1.82 sheets, so area says two.

Here are two ordinary ways to cut it:

  • Split A, panels across the van: two panels at 48 × 70 in and one at 24 × 70 in.
  • Split B, panels along the van: one at 48 × 96 in, one at 22 × 96 in, one at 48 × 24 in and one at 22 × 24 in.

Both cover the same floor. Here they are in the cut list calculator with its default 3.2 mm kerf, and grain unlocked because a subfloor’s face is hidden under the floor covering. The rows are the sheets in the calculator’s own material table.

Sheet Stocked in, per the site’s table Split A, across Split B, along
4 ft × 8 ft (1220 × 2440 mm) US, Canada, UK 3 sheets, 60.7% yield 2 sheets, 91.0% yield
2500 × 1250 mm Continental Europe 3 sheets, 57.8% yield 2 sheets, 86.7% yield
2400 × 1200 mm Australia, New Zealand Will not fit Will not fit
5 ft × 5 ft Baltic birch (1525 × 1525 mm) US, Canada, UK, Europe, Australia Will not fit Will not fit

Yield is the area of the parts as a share of the sheets bought. The rest is offcut.

Split A takes three sheets. On a 4 × 8 sheet, each 48 × 70 in panel uses the full width and leaves a strip about 26 in long. The 24 × 70 in panel needs 70 in of length one way or the other, no strip comes close, so it gets a sheet to itself. The calculator shows that third sheet at 36.4% used.

Split B takes two. The 48 × 96 in panel is a whole sheet. The 22 × 96 in strip comes off the second sheet, and both short pieces come out of the material left beside it, with the 48 × 24 in piece turned on its side.

Same floor, same sheet, and one split costs a whole extra sheet. Fewer, larger pieces are not automatically fewer sheets. Split B does put more seams in the floor, and where those seams land relative to whatever supports the floor is a structural call the calculator does not make. It only counts sheets.

Two more things the table shows:

  • On the common Australian sheet, neither split can be cut. The 48 × 70 in panels in split A and both 96 in panels in split B fit a 2400 × 1200 mm sheet in neither direction. A 48 in piece is 1219.2 mm, and 96 in is 2438.4 mm. The site’s material table also notes that some Australian suppliers stock 2440 × 1220 mm, and on that sheet both splits work as drawn. Confirm which sheet you are buying before you draw anything.
  • Baltic birch fails both. It is 60 in square, and both splits include panels longer than that.

A full-size panel needs a full-size sheet

Split B uses a panel that is exactly one 4 × 8 sheet. That only works if the sheet really is 48 × 96 in.

APA, the US panel trade body, says the “Sized for Spacing” notation often appears on its Rated Sheathing, Rated Sturd-I-Floor and Performance Rated Siding trademarks. It means the manufacturer has made the panel slightly under the traditional 48 by 96 in. APA’s technical topic describes the practice, at the manufacturer’s option, as trimming panels by up to 1/8 in in length and width to encourage proper spacing between panels.

If a sheet has been trimmed at all, a part drawn at a full 48 × 96 in will not come out of it. The calculator’s 4 × 8 entry is 1220 × 2440 mm, so it will not catch a trimmed sheet for you. Measure the sheet, enter it as a custom sheet, and draw any full-width or full-length part to the measured size.

A van is several cut lists, not one

The calculator assumes full sheets of a single thickness at a time, and the methodology page says so. A van build that mixes thicknesses is several cut lists. Group the parts by the thickness you have chosen for each job, then nest each group on its own.

Job What to enter Grain
Floor Each panel at its bounding rectangle Unlocked, if a covering goes over it
Wall and ceiling lining Each panel at its bounding rectangle Locked, if you want the face grain to run one way
Cabinets, bed platform, seating Each part as drawn Locked on parts that show: doors, drawer fronts, end panels

A panel notched around a wheel arch, a window or a rib still costs its full bounding rectangle. The calculator nests rectangles, so it does not know the notch is there. That is the safe way round: the cut-out becomes an offcut you might use, not material the count relies on.

If a lining panel is not a true rectangle, template it in card first, then measure the template at its longest and widest. Measure the panels on each side of the van separately rather than mirroring one.

Furniture: the nest matters as much as the parts

The calculator loads an RV galley carcass as its default parts list, nine pieces in all. It holds them in millimetres, and the inch sizes here are rounded to the nearest 1/16 in.

Part Size (in) As stored (mm) Qty Grain locked
Carcass side 22 13/16 × 35 7/16 580 × 900 2 Yes
Base 22 13/16 × 46 7/16 580 × 1180 1 No
Shelf 22 1/16 × 45 11/16 560 × 1160 2 No
Drawer front 14 15/16 × 22 13/16 380 × 580 3 Yes
Back panel 35 7/16 × 46 7/16 900 × 1180 1 Yes

On a 4 × 8 sheet with the default 3.2 mm kerf, it nests into two sheets at 79.8% yield. The methodology page records that the tool’s first version, which ran a single packing rule, got three sheets at 53% on the same list, with one sheet holding a lone drawer front. The current version runs twelve packing strategies and keeps the best, and this list is now one of its regression tests.

That gap is the case for nesting before you buy. Area says two sheets for this list whichever way you lay it out. A layout that packs the big parts badly can spend a third sheet on one small part, and area cannot tell you that.

Thickness decides which pile a part goes in

The sheet count for a list does not depend on thickness, but which list a part belongs to does. A plan from another market can put a part on the wrong one. This site’s material table treats imperial and metric ply as different products, with these measured thicknesses:

Sold as Actual thickness Sold in Not the same as
3/4 in 18.26 mm US, Canada 18 mm (18.00 mm)
1/2 in 11.91 mm US, Canada 12 mm (12.00 mm)
18 mm 18.00 mm UK, Europe, Australia, NZ 3/4 in (18.26 mm)
12 mm 12.00 mm UK, Europe, Australia, NZ 1/2 in (11.91 mm)

The imperial figures are the actual sizes Inch Calculator lists for those nominal sizes, 23/32 in and 15/32 in, worked out in millimetres. Inch Calculator also notes that measuring with a caliper is the only accurate way to know a sheet’s thickness. Grooves and rebates cut for one product will not fit the other cleanly, so if you follow a plan drawn in the other system, redraw the joinery for the sheet you bought before you nest the parts.

Before you buy

  1. Decide the sheet first. Write its size at the top of every cut list, in the merchant’s own words.
  2. Make one list per thickness. Floor, linings and furniture each go on the list for the thickness you chose for them.
  3. Measure the van and the sheet. Bounding rectangles for notched panels, and a custom sheet size if the sheet is not full size.
  4. Set the kerf to your blade. The calculator’s 3.2 mm default is a starting point, not your saw.
  5. Lock grain only where it shows. Every locked part gives the packer fewer options, and the calculator’s own notes warn to expect a worse yield when most parts are locked.
  6. Try more than one split for the big panels. The floor above went from three sheets to two on the split alone.
  7. Add up per thickness, then decide on spares. On a tight nest, a mis-cut part has no offcut to come from. I would buy one spare sheet of whichever thickness has the tightest nest rather than make a second trip for it.

The calculator counts sheets and draws the nest. It does not sequence your cuts or price anything, and it stops at 400 part instances.

The plywood sheet sizes guide covers what each market sells and why none of the sheets is a conversion of another. If you are laying a new floor over an old one in an RV rather than a bare van, RV flooring covers what to check underneath first. And before any lining goes up, every cable that will run behind it should be in place. The 12V wire size chart sizes those runs.

Sources

Where this guide states a fact rather than an opinion, it came from one of these. Product names are examples of a category, not endorsements, and nothing here is sponsored.

  1. Sized for Spacing, technical topic TT-055 - APA, The Engineered Wood Association
  2. Actual Plywood Thickness and Size - Inch Calculator

Illustrations

The diagrams on this page are illustrations, drawn to explain a concept. They are not photographs of a real cabinet and they carry no measurements, because a diagram that looks precise and is not would be worse than no diagram at all. Anything on this site with numbers on it is generated from the underlying data.