Volt & Grain

Guides / Renovation

Plywood sheet sizes by market (US, UK, EU, AU)

The plywood sheet you can buy depends on where you are. The common formats with a merchant listing for each, why none is a conversion of another, and what that does to a cut list.

Published27 October 2026
Sources11 cited

A plywood sheet is not one size with four names. It is four different products, cut to four different standards, and the one on the rack depends on the country you are standing in. That matters more in a van or an RV than in a house, because a build drawn around one sheet can be impossible to cut from another, and you find that out at the saw.

This page lists what each market actually sells, with a merchant listing for each so you can check me. The sizes are not converted into each other. They are quoted the way the merchant in that market quotes them, in the order that market uses.

What each market sells

Market Sold as Merchant listing
US and Canada 4 ft × 8 ft, listed as an actual 48 in × 96 in Home Depot sanded plywood listing
UK 2440 × 1220 mm B&Q hardwood plywood listing
Continental Europe 2500 × 1250 mm toom Baumarkt multiplex listing
Australia and New Zealand 2400 × 1200 mm, with 2440 × 1220 mm also sold Bunnings structural plywood range, Canterbury Timbers
Baltic birch, most markets 5 ft × 5 ft, 1525 × 1525 mm Capitol City Lumber listing

Three of these look close enough to be the same thing. They are not, and the differences are the kind that change a sheet count.

  • The US sheet at 48 × 96 in works out to 1219 × 2438 mm, so it is the UK sheet to within a couple of millimetres. That is arithmetic, not a merchant claim, and it is the one pair you can treat as the same footprint.
  • The European sheet is 60 mm longer and 30 mm wider than the UK sheet.
  • The Australian sheet is 40 mm shorter and 20 mm narrower than the UK sheet.
  • Baltic birch is square. A nest drawn for any of the others does not apply.

US and Canada: 4 × 8, and read the actual line

The US sheet is sold as 4 ft × 8 ft. On a sanded panel the merchant lists an actual size as well, and on the Home Depot listing above that is 48 in × 96 in, so for furniture-grade ply the nominal and the actual footprint agree.

Structural sheathing is different. APA, the US panel trade body, describes a “Sized for Spacing” mark on its trademark stamp. Where it appears, the mill has trimmed the panel by up to 1/8 in in length and width so that installers leave a gap between sheets on a roof or a wall. That is the right thing for a house and the wrong thing for a cabinet, so if you buy sheathing for a van floor, measure the sheet before you plan a cut that needs the full 96 in.

The thickness is where US buyers get caught. A sheet sold as 3/4 in is listed by Home Depot as a common 23/32 in with an actual thickness of 0.703 in, which is 17.86 mm. Inch Calculator’s nominal to actual table gives the same nominal size as 23/32 in, 18.26 mm. The two figures differ, which is one more reason to measure the sheet you bought. The plies lose moisture, the stack is pressed, and the faces are sanded, and the sheet ends up under its name. More on why that matters below.

UK: 2440 × 1220 mm, the old 8 × 4 in millimetres

British merchants list the sheet in millimetres, long side first. The B&Q listing above is 2440 mm long, 1220 mm wide and 18 mm thick, and gives its weight as 27 kg. People in the trade still call it an eight by four, and that is fair, because it is the same footprint as the US sheet.

The thickness is not the same product as the US one. 18 mm is a metric nominal, not a translation of 3/4 in. The listing says 18 mm and the sheet is cut to 18 mm. Keep that in mind if you are following a US build plan with UK stock.

Continental Europe: 2500 × 1250 mm

The European format is a different sheet, not a rounder version of the British one. The toom listing above is a 2500 × 1250 mm birch multiplex at 12 mm, and Penn Elcom lists a 15 mm birch panel at the same 2500 × 1250 mm, with a listed weight of 32 kg and a thickness tolerance of plus 0.6 mm and minus 0.8 mm.

That tolerance is worth a look. Even a metric sheet sold as 15 mm is a range, and the range is wider on the thin side. For a groove or a rebate, measure the sheet in your hand, not the label.

The extra 60 mm of length and 30 mm of width over the UK sheet is not much, and it is enough that a nest which is tight on 2440 × 1220 mm gains a strip, while a nest drawn for 2500 × 1250 mm can be unbuildable on UK stock. If you are following a German or Dutch van build from the UK, check every long part.

Australia and New Zealand: 2400 × 1200 mm, and sometimes 2440 × 1220 mm

The common Australian sheet is 2400 × 1200 mm. The Bunnings structural plywood range above lists it that way, long side first, in 12 mm among other thicknesses. It divides cleanly into 600 mm and 300 mm, which is simple arithmetic and the reason it is comfortable to work with on a metric drawing.

The catch is that 2440 × 1220 mm is sold in Australia as well. Canterbury Timbers in Sydney lists its marine plywood in 2440 × 1220 mm across a range of thicknesses. So two sheets that differ by 40 mm on the long side sit in the same market, and sometimes in the same yard. Confirm which one you are buying before you draw anything, and do not assume the marine ply is the same size as the structural ply you measured last week.

For an Australian reading a US or UK build plan, the 40 mm is the problem. A layout that uses the full 2440 mm of a UK sheet does not fit a 2400 mm sheet, and no amount of kerf trimming recovers it.

Baltic birch: 5 × 5, and square

Baltic birch is sold in the US as a 5 ft × 5 ft sheet. The Capitol City Lumber listing above is for that size, and 60 in works out to 1524 mm, which is why you will also see it listed as 1525 × 1525 mm.

The usual explanation, which comes from woodworking forums rather than from a mill, is that 1525 mm square is the native format of the Baltic and Russian mills that make it, and the US simply imports it as cut. This page has no manufacturer source for that, so treat it as the folk answer. What is not in doubt is the shape: it is square, and no 4 × 8 nesting diagram applies to it.

For a van or boat it has one practical consequence. A square sheet gives you no long run, so anything over 1525 mm long is two pieces or a different sheet. It also fits through some doors and into some vehicles that a 2440 mm sheet does not, which is a real advantage when you are the delivery van.

Thickness is the same story, smaller

The sheet footprint is one trap. The thickness is the other, and it is the one that ruins joinery rather than cut lists.

Sold as Measures Market Basis
3/4 in 18.26 mm US, Canada Inch Calculator nominal to actual table
18 mm 18.0 mm UK, EU, AU, NZ Metric nominal, cut to size
1/2 in 11.91 mm US, Canada Inch Calculator
12 mm 12.0 mm UK, EU, AU, NZ Metric nominal
3/8 in 9.13 mm US, Canada Inch Calculator
9 mm 9.0 mm UK, EU, AU, NZ Metric nominal

A quarter of a millimetre sounds like nothing. Cut a dado to take a 3/4 in panel and slide an 18 mm one into it and the joint has a quarter of a millimetre of slop, which is enough for the panel to move. Cut the groove for 18 mm and push a 3/4 in panel at it and it does not go in.

The reference tables mark which pairs should never be swapped. The rule is simple: fit the joinery to the sheet in the shop, and never to the name on a plan written somewhere else.

What this does to a van or RV build

Four things to do on every sheet goods job because of the above.

  1. Decide the market before the drawing. The sheet size goes at the top of the cut list, in the merchant’s own words. If you are working from someone else’s plan, write their sheet next to yours and look for every part that uses the full length or width.
  2. Measure the first sheet home. Length, width, thickness at three places. Structural sheathing may have been trimmed, metric sheets have a tolerance, and the drawing gets the measured number, not the label.
  3. Keep the grain along the length. Plywood face grain runs along the long side of the sheet. On a 2400 mm sheet that is 40 mm less grain-long run than on a 2440 mm one, and parts that must show long grain are the first to stop fitting.
  4. Nest it on the sheet you can buy. The cut list calculator counts sheets on US, UK, European, Australian and Baltic birch stock at once, and tells you when a layout is impossible on one of them. That is the check that is easiest to get wrong with a pencil.

If the subfloor is part of the job, RV flooring covers what to check underneath before any of this matters. If you are only replacing fronts, replacing RV cabinet doors deals with the weight question, which is the other thing a sheet of plywood does to a vehicle.

Sources

Where this guide states a fact rather than an opinion, it came from one of these. Product names are examples of a category, not endorsements, and nothing here is sponsored.

  1. Sanded Plywood, Common 23/32 in x 4 ft x 8 ft, Actual 0.703 in x 48 in x 96 in - The Home Depot
  2. Sized for Spacing, technical topic TT-055 - APA, The Engineered Wood Association
  3. Actual Plywood Thickness and Size - Inch Calculator
  4. Hardwood Plywood (L)2440mm (W)1220mm (T)18mm - B&Q
  5. Multiplexplatte unbehandelt 2500 x 1250 x 12 mm - toom Baumarkt
  6. 15mm thick birch wood panel, 2500 x 1250 mm - Penn Elcom
  7. Structural plywood range - Bunnings Warehouse Australia
  8. Marine Plywood 2440 x 1220 x 4mm - Canterbury Timbers, Sydney
  9. 5x5 Baltic Birch Plywood - Capitol City Lumber
  10. Why is Baltic Birch 5X5 instead of 4X8? - Sawmill Creek forum
  11. Plywood Sheet Sizes - CutList

Illustrations

The diagrams on this page are illustrations, drawn to explain a concept. They are not photographs of a real cabinet and they carry no measurements, because a diagram that looks precise and is not would be worse than no diagram at all. Anything on this site with numbers on it is generated from the underlying data.